Showing results: 16 - 30 of 412 items found.
-
N1231B -
Keysight Technologies
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
iWave Systems Technologies
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
iWave Systems Technologies
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
iWave Systems Technologies
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
N1231A -
Keysight Technologies
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Innerspec Technologies, Inc
The PCI-8 is an 8-channel, PCI-based AE system on a board. Its 8 high-speed AE channels offer simultaneous AE data acquisition, waveform processing and data transfer. The board’s standard PCI form factor enables installation in standard PCs, as well as in any of Physical Acoustics’ specialized AE system chassis, while the PCI bus enables AE data transfer at speeds of up to 132 Mb/s, at a frequency range of 1 kHz to 400 kHz.
-
332D-11 VG -
Tech-Aid Products
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
Composite Family -
Test Electronics
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
-
EverythingPCB
Printed Circuit Board Testing and Repair Services CM Wings Board Testing Inc. was founded in 1983. Its founding was a direct response to theneed for a truly customer service oriented facility for printed circuit board test and repair.
-
Test Probes -
JYEBAO Co., Ltd.
An excellent way to sample a signal within a circuit, without having to design-in test points into a circuit board.
-
TOPTEST GmbH
Development of additional hardware components in-houseCreation of the layout of the developed circuit boards and subsequent production outside the companyAssembly of the printed circuit boardsCreation of additional circuits for test adapters
-
8022 -
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
-
Circuit Check, Inc.
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.